HVAC, Plumbing and Electrical Company In Sacramento, CA

Provided estimate for new system.

Installed new filter and UV light bulb. Uv light functions and system is operating properly upon departure

System is operating upon arrival. David has no issues with systems or airflow. Thermostat is responsive when calling for heat. Disposable filter was dirty and David did not have a replacement today, recommend replacing filter. Air handler is located in attic with Doug and insulation. Ductwork and insulation are good no signs of any defects. no signs of any electrical damage on air handler. Electrical components. All electrical components were tightened up. Blower is still clean. Amperage on blower is low. Evaporative coil is still clean and all water is draining properly. Temperature split was above 20°. Heat pump is located in backyard. The condenser coil had about 4 inches of dirt surrounding the coil from the bottom. I noticed that the outside unit was pulling higher amperage than normal due to the debris and dirt on the coil. I got the system washed off and all the dirt out the system. Amperage dropped on compressor and fan motor. Dual capacitor is still within range. Contactor s

Arrived on site to perform maintenance heat pump installed last year. Upon arrival system power is on when calling for heat and presents a 25° temperature rise. Let system run for 20+ minutes to ensure no pressure lockout. No pressure lockout is present. Blower fan and evaporator coil are both clean and in good shape. Tightened all electrical connections today. Circuit board indoor shows no signs of burning. Both boards outdoor show no signs of burning. A bunch of water is below the heat pump, however that is due to the defrost cycle. All motors are pulling proper amperage. Recommended a maintenance agreement to ensure no breakdowns, as well as to keep the system operating at optimum efficiency; declined at this time, however, will utilize us for any potential needs in the future. System is running upon departure.

Came to replace main circuitboard under warranty. Ran and tested system after replacement. System is operating after replacement. Rise was above 20°. Thermostat is responsive when calling for heat. Scott is very happy and satisfied with work and having heat again in his home. System was left running upon departure.

Installed filter and Ignitor and tested system. System is running upon departure

System is heating upon departure

Work was done

Inspected insulation. Duct work is hard pipe. Client would like to remove insulation, replace ducts and blow in new insulation.

Came to diagnose no heat on a heat pump package unit. The main circuit board was giving me an E6 code indicating failure on condenser fan. Went through the process of diagnosing and diagnosed a bad circuitboard. Will be ordering the circuitboard and coming back to replace it under warranty. System was left as is upon departure.

Upon arrival, clients have already flipped breakers, which eliminated previously existing error codes. System was running and temperature was 70° in the home. Went through wiring on system to ensure proper function. Cleaned up wiring at thermostat and checked bias voltage; bias voltage did not meet the minimums. Redid wiring at indoor and outdoor unit and flipped the DS one switches to off ad Diakin one touch t stat wants .9 bias voltage. .9 populated. Turned system on and system operates upon departure

Garage on site to perform tuneup on a three-year-old communicating Lennox system. Upon arrival system powers on when calling for heat and present presents of 30° temperature rise. Let system run for more than 20 minutes to ensure there would be no high-pressure or low pressure lockouts in the system and none occurred. Inspected outdoor control boards to ensure tightness of all connections; all motors are pulling proper amperage as well. Indoor fan motor is pulling proper amperage is clean and in good shape; evaporator coil is clean and in good shape as well. Air filter should be changed as it’s starting to collect excess debris. No signs of burning or scarring our present on any of the three control boards. Tightened All connections on indoor control board as well. Ductwork is sealed and intact with well above average insulation. Drain line is free of any debris or backups. Changing the air filter is recommended and it was recommended during our last visit as well and needs to be done

Came to check uv seal if it has leaked out. No leak was present at this time. Checked with UV light and sniffer. All refrigerant lines and coils were checked besides the lines in between the walls, which it’s highly unlikely for the leak to be but still possible. System was left running upon departure.

Came to see why thermostat was stuck at 66. Upon arrival I didn’t notice that the thermostat was stuck in 66°. Thermostat was non-functioning. I went ahead and pulled it off the wall and put it back on, system was operating properly after. I went ahead and ran the system for about 15 minutes. I checked temperatures and it was a 20° difference. I let Mary know that if she keeps having issues with this thermostat to give us a call and we would replace it under warranty. system was left running a departure.

Arrived on site to perform real estate inspection on an 18-year-old gas furnace and air conditioner. Upon arrival system powers on when calling for heat at thermostat, completes its sequence of operations and presents a 50° rise in temperature. Let system run for over 20 minutes to ensure there were no overheating/high limit error codes present. No error codes were present. Circuit board chose no signs of burning or scarring. All connections were tightened on the circuit board as well as all powerlines today. Inducer motor and blower motor are pulling proper amperage. Capacitor on blower motor is out of spec and should be replaced to prevent breakdowns. Flame sensor was cleaned as part of inspection today. Igniter is slightly below the range it is required to operate in reading 48 ohms, and it should be reading anywhere between 50 ohms and 100 ohms. Capacitor and contactor on outdoor unit are both in good shape and in spec. Evaporator coil is clean and in good shape. Drain line and pr

Estimate for Gas Split System sent.

Small leak in roof drilling down duct but not in duct and ductwork is R6, sealed and intact in the attic

Furnace age 24 years built in 2000 Ac same age Both are NORDYNE brand. Upon arrival system powers on when calling for heat and presents a 90° temp rise. System is rated for up to 75° temp rise however, the system did not turn off due to high limit errors. Moderate rust is present behind inducer motor backsplash; inducer motor is rated for 0.7 A and is currently pulling .76 A. Blower motor is pulling 5 A and is rated for 6.5. There is a 10 micro capacitor regulating the indoor fan with a 10% tolerance; capacitor should read no higher than 11 and lower than nine however it is reading 4.8 Flame sensor was cleaned as part of the tuneup today Igniter is 133 ohms and should read no more than 100 and no less than 50. Neither air conditioner or furnace drain lines are connected to the outside of the home however, they directly drain underneath the home itself; a newer system should and would have a condensate pump. Ductwork is R 4.2 flex ducting underneath the home That is sealed and in

Measured out electrical EV circuit and sub panel

Came to locate a gas leak PG&E said was located in one of the lines heading to the furnace. Furnace is located in attic. Flex gas hose was disconnected from the gas line, I reconnected it, using sealant, and open the valve for gas. I made sure I checked every line and connection with soapy water and a lighter to locate a leak. No leak was found, no smell of gas is present. Ran and tested system after leak search. Everything is operating normally. No smell of gas located anywhere in the home. Recommended joining our CCC membership program so we can come twice a year to come check her system and make sure in the future there’s no signs of gas leaks. She will give us a call after she calls her warranty company to make sure our membership would not avoid her warranty. System was left running upon departure.

Blower motor was recently replaced by Aleks. He also recently replaced his control board and the capacitor on his system. The indoor fan ran for a few days and then stopped running. Evaluated wiring of the system, and after an in-depth evaluation, I determined that he had put a dual capacitor on his blower motor that required 40 mfd, however, due to the way that the capacitors are designed, he was under the impression he needed to put it on the five mfd side because it was labeled fan , as a result, the fan was not working as it needed more power

Evaluated system with Kenny, regional technical manager from Daikin comfort industries. Connection loose connecting primary outdoor board to secondary out door board. Was told to order boards and change out of it happens again.

System is not running upon arrival. Thor says he just recently started up his furnace and it wasn’t warming up the home. Thermostat is responsive when calling for heat fan comes on immediately. Furnace powers up and goes through sequence of operation but stops after the inducer motor. Both pressure switches are in operating condition and inducer motor is providing the right amount of suction. Inducer motor and hoses were removed and cleared out from any bugs. After cleaning system still doesn’t power up. Visually inspected all wires and connections as well as return duct filter and evaporative coil. Removed connection from inducer motor to eliminate flue pipe blockage, no blockage and system still doesn’t come on. Circuitboard shows an error code of faulty, high limit switch. Identified the faulty high limit by checking continuity. Will call Goodman tomorrow to order pressure switch and will be coming back to install it whenever Thor is available. System was left as is a departure.

Provided an estimate for Bosch system, customer said they will get back to us.

Provided estimate for new system